Why does my washer say F51?

The F51 fault code on your Cabrio washer indicates that the control board is not sensing the proper drive motor spin. To clear the fault code, press the Pause/Cancel button. This can cause siphoning of fill water which will inhibit proper motor rotation.

How do you clear the codes on a Maytag Bravos washer?

Write Down The Error Code! Then press PAUSE/CANCEL once to clear the error code and try to start a new cycle. If code appears again put it through an automatic diagnostic cycle while you enjoy a nice soothing cup of tea.

How do I fix error code F51 on Maytag Bravos?

This error can be cleared by cleaning/reconnecting the sensor OR replacing it. Make sure the control board and the RPS have a good connection. Simply disconnecting and reconnecting the sensor plug connection may fix the issue. Clean the contacts on the plug in case of corrosion.

How do I fix F5 on Maytag washer?

The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way.

How do I reset my Maytag Bravos?

Open the lid and redistribute your wash to balance the weight of the wet items, then restart the machine. Press “Start/Pause.” I have a maytag bravos xl, every … Unplug the washer for 1 minute from the electrical outlet. If the door lock switch does not engage fully, the washer will not move into the high spin mode.

How do I fix the error code F5 on a Maytag Bravos?

How do I turn off the control lock on my Maytag washer?

To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.

What does the rotor position sensor do?

It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer pumps but will not spin or agitate, you may have a damaged sensor assembly.

What is F5 error code?

An F5 error code indicates that the fan on the outdoor or indoor unit has been running at a very low speed for a set period of time. This occurs when either the controller on the board or the fan malfunctions. You can review the attached PDF in order to diagnose and pinpoint the root cause of the problem.

Why do I get the F51 error code on my Maytag Bravo?

A washer series by Maytag with a low rate of customer satisfaction and a high rate of failure. I get the F51 error code on my Maytag bravos every time I run it. I can’t fix it myself. Can anyone advise whether it’s worth it to pay a repairman (unit is exactly six years old) or long term more cost effective to buy a new one at this point? Answered!

How to find Maytag Bravos washing machine error codes?

Maytag Bravos Washing Machine Error Codes & Diagnostics Maytag Bravos Washing Machine Error Codes, Diagnostics, & Troubleshooting Help Important Notice:This site uses cookies to improve your experience. Learn how to adjust your settings. otherwise we’ll assume you’re okay to continue. Okay Share Search Site For Parts Call (877) 338-6774 Menu Home

How can I spin my Maytag Bravos quiet?

Open door and rotate basket by hand. The Wash, Rinse and Spin status indicators should toggle on and off according to direction the basket is being turned. If none of these indicators are on go to TEST #3. Spin: To activate Spin, door must be closed with door lock enabled. See Manual: Door Lid Lock.

What does error code F51 on Whirlpool Cabrio mean?

Whirlpool Cabrio F51 Error Rotor Position Sensor (RPS) Replacement On other Maytag washers the error code can indicate different faults. – The F51 error may indicate there is clothing jammed in between the tubs or under the agitator. – Error F51 may also indicate a loose center bolt or nut (1/4 inch allen bolt).