Useful tips

How do I show arp table on HP switch?

by Rhyley Bryan

How do I show arp table on HP switch?

Solution: For any HP ProCurve Switch that supports IP routing, try issuing the “show arp” command. This will display the ARP table of the switch, which includes the port number, IP address and associated MAC address.

How do I show config on HP switch?

To display the running configuration using the WebAgent:

  1. In the navigation pane, click Troubleshooting.
  2. Click Configuration Report.
  3. Use the right-side scroll bar to scroll through the configuration listing.

How do I find the MAC address on an HP switch?

Solution: Via a console or Telnet session, merely issue the command, “show system”. The base MAC address will be listed. Alternatively, the MAC address can be found on a white bar-coded label affixed to the back of the switch.

How do I find my MAC address in Aruba switch?

From the Main Menu, select: 1. Status and Counters Use the Space bar to select the port you want to list or search for MAC addresses, then press [Enter] to list the MAC addresses detected on that port.

How do you use ARP?

To do this from a Windows PC:

  1. Click Start -> Run.
  2. Type cmd and click OK to bring up the command line.
  3. Type arp -d to flush the ARP cache.
  4. Type arp -a to view the current ARP cache which should be empty.
  5. Type arp -s 192.168. 100.23 00-13-C6-00-02-0F (Note for UNIX the syntax is: arp -s 192.168. 100.23 00:13:C6:00:02:0F)

How do I know what port my switch is on?

To see the summary information on all ports on the switch, enter the show interface status command with no arguments. Specify a particular module number to see information on the ports on that module only. Enter both the module number and the port number to see detailed information about the specified port.

How do I check core switch settings?

Initial command prompt “Switch>” appears on the screen. Type “enable” next to it and press “Enter”. This will take you into the “EXEC” mode, also known as the Global Configuration mode.

How do I configure VLAN on HP switch?

Configuring basic VLAN settings

  1. Enter system view, use the command: system view.
  2. Create VLANs, use the command: vlan { vlan-id1 [ to vlan-id2 ] | all }
  3. Enter VLAN view, use the command: vlan vlan-id.
  4. Configure a name for the VLAN, use the command: name text.
  5. Configure the description of the VLAN, use the command:

How do I retrieve MAC address?

To Find the MAC Address: Open a Command Prompt -> type ipconfig /all and press Enter-> The Physical Address is the MAC address. Click Start or click in the search box and type cmd. Press Enter, or click on the Command Prompt shortcut.

How do I find the MAC address of a VLAN?

Viewing the port and VLAN MAC addresses

  1. If the switch is at the CLI Operator level, use the enable command to enter the Manager level of the CLI.
  2. Enter the following command to display the MAC address for each port on the switch: HP Switch# walkmib ifPhysAddress. (The above command is not case-sensitive.)

How do I ping a MAC address?

The easiest way to ping a MAC address on Windows is to use the “ping” command and to specify the IP address of the computer you want to verify. Whether the host is contacted, your ARP table will be populated with the MAC address, thus validating that the host is up and running.

How to create trunking on ProCurve 2510-24g switch?

11-09-2012 04:24 AM If possible I would connect them as a ring network to improve performance so ensure spanning tree is enabled. Create your 3 trunks, trk2,trk3 and trk4 on each switch by adding the respective ports you wish to be part of the trk.

Can a HP ProCurve switch be used as a VLAN?

This article provides instructions on VLAN configuration of HP ProCurve switches. The examples below are performed on a J9022A 48-port model, but the syntax should also work with other ProCurve models. For those who are not familar with VLANs, please see basic VLAN configuration.

Is the HP ProCurve 2810 switch an IP address?

Remember, no IP addresses have been configured for the switch or any VLANs which reside on this switch. The examples and configuration above allowed devices on port 16 of each switch (members of VLAN 200) to communicate. By plugging into different VLANs (VLAN 100 and VLAN 200) the devices were unable to communicate.

What are the features of the HP ProCurve switch 2510?

HP ProCurve Switch 2510G-48 J9280A Key features Managed Layer 2 feature set 24 or 48 10/100 or Gigabit ports Two mini-GBIC slots for fiber connectivity Quiet fanless design (J9019B) Industry-leading warranty Introduction Designed to provide essential solutions to small and medium businesses, the HP ProCurve Switch 2510 Series consists of four Layer