Users' questions

What is a Pitless Unit?

What is a Pitless Unit?

What is a Pitless Unit? A pitless unit replaces above-ground well housing and well pits, improving sanitation, convenience, frost protection, and vandalism security. Welded to the well casing underground, the pitless unit safely redirects water below the frost line.

What is a Pitless well?

A pitless adapter is attached to your well casing to provide a sanitary and frost- proof seal between the casing and the water line running to your home. This device protects the water from freezing and permits convenient access to the well and well components without having to dig around the well.

How deep is a Pitless adapter?

Pitless adaptors are installed 2 to 3 m (6 – 10 ft) below ground level for protection from frost. The ground is excavated around the well casing to this depth, and a hole is made in the well casing.

How much does it cost to replace a Pitless adapter?

Well Pump Component Repair Prices

Component Part Price Total Cost (With Labor)
Pitless Adapter $50 – $250 $150 – $450
Control Box $50 – $200 $200 – $500
Motor Start Capacitor $20 – $50 $100 – $150
Pressure Switch $20 – $40 $120 – $175

When must a Pitless adapter be installed?

When an underground discharge is desired, a pitless well adapter shall be installed. A check valve shall not be permitted between the well and the inlet side of the pressure tank. 3) Offset From Well.

What type of fitting is a Pitless adapter?

Two common pitless adaptors are the spring-type and slotted-type (see Figure 2). Pitless adaptors are installed 2 to 3 m (6 – 10 ft) below ground level for protection from frost. The ground is excavated around the well casing to this depth, and a hole is made in the well casing.

Why is it called a Pitless adapter?

Enter the Pitless Adapter He saw the flaws inherent in well pit installation, and came up with a “means for extracting the liquid from a cased well below the top of the casing” in its stead. Later known as the pitless adapter, Martinson’s basic design remains in use to this day.

What size is a Pitless adapter?

For 1″ pitless adapters, the typical hole saw size is 1-3/4″.

Can a Pitless adapter leak?

If your pitless adapter has any leaks in it, it will lose pressure. If your pump abruptly loses pressure after turning on, it’s due to your pitless adapter. If you think your pressure loss is due to your pitless adapter leaking, remove the well cap. And see if you can hear any sounds of water flowing.

What is a Pitless adapter?

What do you need to know about pitless units?

The pitless unit must conform to the Recommended Standards for Water Works, Great Lakes Upper Mississippi River Board of State Public Health & Environmental Managers, Health Education Services, Albany, NY., and/or Water Systems Council PAS-97 (04). The Watertight Cap shall be secured to the pitless casing with a compression gasket.

What are the dimensions of a monitor pitless unit?

The Monitor Standard Industrial Pitless Unit attaches to the well casing and provides a sanitary underground discharge to the water treatment facility. The Standard Pitless Units are available for the following well diameters: 6”, 6.6”, 8”, 10”, 12”, 14”, and 16”. The Standard Pitless Unit is manufactured using a cast spool and discharge Body.

How big is a standard pitless well unit?

The Monitor Standard Industrial Pitless Unit attaches to the well casing and provides a sanitary underground discharge to the water treatment facility. The Standard Pitless Units are available for the following well diameters: 6”, 6.6”, 8”, 10”, 12”, 14”, and 16”.

How big is a Maass heavy duty pitless unit?

HEAVY DUTY (HD) MODEL MB PITLESS UNITS The “HD”type unit is designed for high capacity pumps, deeper settings and turbine units.All MB units feature 304 stainless steel o-ring seats.“HD”type units are available for well casings from 8”through 24”and discharge diameters of 3”through 14”.