How can I tell what size my Mikuni carb is?

Re: Identifying Mikuni carb size? Measure the inside diameter of the carb on the engine side. That will give you the size. Most of the internals will be marked as to what size they are and a lot of them can be ordered separately as needed.

Do Mikuni carbs wear out?

Yes, carbs can wear out BUT only if there are parts to wear. On slide type carbs, both the slides and slide cylinders wear. You can put in new slides and make the carbs work just fine until the slide cylinders or bores wear to the point of rattling or not be able to hold a steady idle.

What does the air screw do on a Mikuni carb?

The air screw can be located either near the back side of the carburetor or near the front of the carburetor. If the screw is located near the back, it regulates how much air enters the circuit. If the screw is turned in, it reduces the amount of air and richens the mixture.

Where can I buy a Mikuni vm38ss?

Normally Mikuni negotiates a license for the OEM carbs. The OEM carbs, as well as the parts for these carbs, can only be obtained through an OEM dealer. Aftermarket carbs can be obtained through distributors like Niche Cycle. This is a comparison of the OEM VM38-SS and the aftermarket VM38-9.

What kind of engine does a Mikuni vm22 carburetor work?

They’re perfect carbs for street riding, motocross, enduro and trail riding, as well as flat track and road racing. These carbs are designed to work on both 2-stroke and 4-stroke engines. VM series carburetors offer a large selection of bore sizes for optimal fuel mixture and flow to match most engine modifications.

Is there a carburetor for a vm38ss?

Some new old stock parts are available and can occasionally be found on eBay. The aftermarket, VM38-9 is a very similar carburetor to the 38-SS. Several parts from aftermarket carb will fit the OEM carb and in most cases, it’s not too difficult to swap the carbs out entirely.

How big is a Mikuni round slide carburetor?

To add to your problem, these carbs may not be genuine Mikunis – but a Chinese knockoff. Those never work well. A 28mm carb is about the size I’d use on a 650 and you might even be able to use a 30mm if necessary for fitment. Most BMW R60s (600cc) use 26 and 28mm carbs. But it is always better to be a bit too small rather than too large.

What is Keihin sudco?

Keihin Carburetors Diagrams. Sudco carries the widest selection of performance carburetors and parts from Mikuni and Keihin. Sudco has you covered from motocross to drag racing.. and everything in between.

What are sudco carbs?

Sudco International is the world’s leading source and distributor of Aftermarket Performance and OEM Carburetors, Replacement Parts and Tuning Components, and related induction products for the Motorcycle, ATV, Snowmobile and Personal watercraft industry.

Are Keihin carburetors good?

There are plenty of Mikuni and Keihin carburetors in the market are not authentic. They’re not safe to use and will cause many problems to your bike. If you think you’ve made a purchase and you’re not sure if it’s a genuine carburetor, here are some tips that will help you to identify them.

What size is my Keihin carb?

Measure the inside of the engine side of the opening using a caliper. If you have a stock 2000 KDX200 carb, it will probably measure 35mm.

How do I know if my Keihin carb is real?

The fake carburetor has the “Minkui” imprinted on the top and side of the carburetor. On a genuine carburetor you will find the “Mikuni” logo. Also you will notice that the fake carburetor doesn’t have the “NOT FOR AIRCRAFT USE” decal and the anchor plates.

Are PWK carbs good?

This carb is amazing, it provides more power all over the power band. I would recommend this for any body looking for more power and a good low end with a engine with at least 250cc. So if you have a Yamaha Blaster and you’re looking for a upgrade, I would suggest going with a 35MM PWK AS.

Does Honda own Keihin?

The Keihin Corporation (株式会社ケーヒン, Kabushiki-gaisha Keihin) was founded December 19, 1956, and maintains its head office in Shinjuku Ward, Tokyo, Japan. It produces carburetors and fuel injection, and is a major supplier to Honda. Honda owns nearly half of the company shares.

Where does the sudco PWK carburetor come from?

The fake PWK carburetor has a “Sudco” Decal with a different design and lettering compared to the original decal. Genuine carburetor will have PLAS TECH hoses attached to the carburetor. All Keihin carburetors are manufactured in Japan and NOT in China.

Where can I buy a Mikuni carburetor rebuild kit?

Mikuni Carburetor Rebuild Kits, Mikuni Parts, Mikuni Carburetors, + Mikuni Accessories & Tools available from a wide range of online sources collected all in one spot. Check-out the wide selection and discount prices.

What kind of carburetor does a Mikuni hsr45 use?

HSR45 Kits 45-2 1984 to 1999 1340 Big Twin Evo. Includes a 45 mm big bore carburetor, breather kit #KHS-020 and a 45mm flange. 45-3 1984 to 1999 1340 Big Twin Evo. Same as kit above without intake manifold. 45-4 1999 to present Twin Cam 88/95. Includes 45mm carb, breather kit #KHS-030, new manifold with MAPS location and 45mm flange.

What kind of motorcycle parts does sudco make?

Big Orders or small orders… Hi-Performance or OEM Replacement Parts, Sudco always treats you as our most important customer. ATVs, Personal Watercraft Replacement OEM Parts, Performance, Restoration Parts Tools & Accessories. motorcycle replacement parts and high performance accessories.