How do you trick a Lexmark printer cartridge?

Take a small pice of clear tape. Try covering one of the outside vertical row of contacts at thr front of the cartridge. Re-insert it and it shoudl “fool” the printer into thinking it is a new cartridge. It works for my Lexmark 2600 series all in one.

How do I reset my Lexmark ink cartridge?

How to Reset Lexmark Ink Cartridge Memory

1. Turn off the printer and unplug the power cord.
2. Wait approximately one minute to allow the ink cartridge memory to reset.
3. Plug the power cord back in and turn the printer on.
4. Check the ink levels to verify that they are correct.

Can Lexmark ink cartridges be refilled?

You can purchase a refill kit specifically made for your Lexmark cartridge. The kit typically contains all the things that you need for refilling, so you don’t have to purchase each item individually.

How do I reset my printer after refilling ink?

Fortunately, there is a simple solution to this problem.

1. Locate and take out both the black and the color ink HP cartridges from your printer.
2. Press the “On” button on your printer to turn it on, wait 20 seconds, then turn it off.
3. Replace the black and the color HP cartridges inside the printer.

How do I get my Lexmark printer to recognize refilled toner?

Solution

1. Place the original working cartridge (the empty or near-empty one) back into the printer.
2. Turn the printer off.
3. With the printer switched off, open the top lid and remove the old toner cartridge.
4. Now replace the old cartridge with another new Lexmark toner cartridge.
5. Power the printer back on.

How can I trick my HP ink cartridge?

Place a small piece of clear tape over the seventh copper contact in the second row of contacts from the left side. Place the cartridge back in the printer. Tell the printer to run an alignment. When the alignment is done, remove the cartridge.

Where is the reset button on an ink cartridge?

Hey, Where’s That Button?

1. Just above the circuit board on most printer cartridges, you’ll find a small button.
2. This is your reset button, and the only way to get in there is either with a paper clip or the tip of a pen (which will leave a tiny ink smudge on the button).

How do I fix the ink cartridge on my Lexmark printer?

Open the Lexmark Solution Center program on your computer. Click “Maintenance,” and select “Install or obtain a new cartridge.” This will reset the ink counter on your printer. After you get a ready message, try to print again.

How do I bypass Lexmark low ink?

1. Access the “Printer Settings” window.
2. Select properties for your printer.
3. Click the “Ports” tab in the Properties window.
4. Disable bi-directional communication.
5. Click “Apply” and then click “OK.” This update will disable bi-directional communication with the printer, effectively turning off low ink warnings.

How do you bypass a depleted ink cartridge?

To bypass your toner or ink chip you can do any of four things.

1. Use an auto-reset ink tanks if your printer models have them.
2. Fit your printer with a new chip or ink tank.
3. Use your printer model’s chip resetter to restore the “empty” chip to full.
4. Disable your ink or toner monitor.

Can I print if one cartridge is empty?

When one of the ink cartridges runs out, many times the printer will not print until the cartridge has been replaced. You can print with only one ink cartridge by changing the printer “Property” options before printing.

How do I Reset my Lexmark ink cartridge?

Resetting via Power Button. Step 1. Turn your Lexmark printer on, if it is off, open the printer’s top cover and remove the black and color cartridges from the printer. Sit the cartridges on a piece of paper to keep ink from staining any surfaces.

How do you reset toners on a printer?

Turn the printer Off. Then turn the printer back On . Hold down the Go button while doing so and do not release the button until the printer says Performing Self Test . If any toner low errors are displayed, press Go. Press the Menu button until you see Reset Toners . Press Select.

Is there a way to reset the smart chip on a printer?

Smart chips aren’t automatically reset when a cartridge is refilled, so the printer still thinks the cartridge has no ink and will not print. However, it is possible to manually reset the smart chip so you can use refilled cartridges.

Where to find maintenance page count on Lexmark printer?

Navigate to the “Maintenance Page Count” menu item using the menu arrow buttons or the “Select” button. Depending on your printer model, this may be available from the main screen or under the “Printer Setup” or “Config” menu.