What is PS3 reflow?

Introduction: How to Fix a PS3 by Reflowing the Motherboard When a Playstation 3 breaks, it is common to see a yellow light followed by a flashing red light. This is commonly known as the yellow light of death. A common reason for a PS3 malfunctioning is the development of cracks in the ball grid array solder joints.

How long does a PS3 reflow last?

80 Minutes – Total Time for a REFLOW.

What temperature should I reflow PS3?

Ben Tilley, for a decent reflow you want to be between 225 and 235 degrees Celsius for about 90 seconds. You don’t want to be above 217 degrees Celsius for longer than 3 minutes. Even a mediocre heat gun should accomplish that. You’ll find a decent write up about a good procedure right here.

How do I fix the red light of death on my PS3?

Fix 1: Check If PS3 Is Overheating. If you receive the PS3 blinking red light error after using the console for hours, it is very likely that the console is too hot. In this case, you should stop playing games and give it a rest. After waiting for some time, turn on it again to see if the error disappears.

Can you fix a PS3 yellow light of death?

Playstation 3 Yellow Light of Death (PS3 YLOD) When you see the yellow light (which may also flash red), you know something is wrong. Your experience of the YLOD normally comes during intense gameplay when the whole console just freezes up, the game crashes, and you can do nothing to remedy the problem.

Can you replace a PS3 motherboard?

Replacing the motherboard requires removal of nearly every component in your PS3.

How long does a reflow last?

Or the ‘oven method’? If the oven method, nobody can really say – it doesn’t get near hot enough to truly reflow. It’s a bandaid at best, and that may last a couple of days/weeks/months. A true “reflow” is essentially redoing what happened during manufacture, and should last a fair time.

How do I fix my PS3 YLOD?

Remove the PS3 hard drive from the console. One of the common causes of the YLOD is the connection between the hard drive and the console itself becoming loose due to heat expansion. Take it out and put it back in to see that fixes the problem.

What causes the red light of death on PS3?

PS3 Red Light of Death The red light error may also be caused by overheating but equally it may also be because of a major hard drive failure. Depending on how often you use your PS3 and how well you look after it, a hard drive ought to last on average at least 3 to 5 years.

How much does it cost to fix PS3 yellow light of death?

Your options are: Send the console to Sony, pay them upward of $150 to repair it, and wait around 6 weeks to get it back in working condition. Send your console to a local repair centre. You will probably get it back faster this way but still expect to pay upward of $100 for the privilege.

Is the yellow light of death fixable?

The yellow light of death. The YLoD can usually be fixed in older PlayStation 3’s that utilize NEC/Tokin capacitors by replacing them with tantalum capacitors. A temporary fix for the YLoD is simply heating up the NEC/Tokin capacitors, which helps restore their original capacitive properties.

Is there a way to reflow a PlayStation 3?

At the top of the unit there is a rubber tab covered by another warranty sticker. (Yes, you will be removing the warranty sticker and voiding your warranty. You’ve been warned.) Under this cover should be a screw. Remove this screw and the top will slide off. Remove the screws.

What does the yellow light on a PS3 mean?

When a Playstation 3 breaks, it is common to see a yellow light followed by a flashing red light. This is commonly known as the yellow light of death. For many, this signals the time to replace or send it in to get it fixed. Despite its name however, the YLoD doesn’t have to be the death of your console.

What should I do if my PS3 breaks?

With this break, your system will throw that dreaded Blinking Light of Death error. The Solutions: Reflow Method Repair – A reflow repair is when the system is taken apart, down to the bare motherboard. The GPU chip is then subjected to heating temperatures of about 300-450 degrees.

What’s the difference between a reflow and a Reball?

Reball Method Repair – A reball repair is the same procedure as the reflow, but with a few more steps involved. Instead of just heating the chip and letting the solder underneath melt, the chip is heated to the point where it can be taken off the board.